PRODUCTION OF REINFORCING ROLLING IN HANKS ON MILL 150 IN ACCORDANCE WITH REQUIREMENTS STB 1704–2006

PRODUCTION OF REINFORCING ROLLING IN HANKS ON MILL 150 IN ACCORDANCE WITH REQUIREMENTS STB 1704–2006

It is shown that putting into operation of the standard STB 1704-2006 will enable to provide building sector with fittings of domestic production cheaper as compared to imported fittings.

Saved in:

Bibliographic Details
Main Author:	V. V. Savinkov
Format:	Article
Language:	English
Published:	Belarusian National Technical University 2010-11-01
Series:	Литьë и металлургия
Online Access:	https://lim.bntu.by/jour/article/view/769
Tags:	Add Tag No Tags, Be the first to tag this record!

Similar Items

ASSESSMENT OF QUALITATIVE CHARACTERISTICS OF NONPRESTRESSED REINFORCEMENT OF GRADE S500 ACCORDING TO STB 1704–2012 IN VIEW OF THE MAIN EUROPEAN NORMS
by: T. A. Akhmetov, et al.
Published: (2014-11-01)

PECULIARITIES OF ROD PRODUCTION OUT OF LOW-ALLOYED STEEL ON THE MILL 150
by: V. I. Shcherbakov, et al.
Published: (2006-05-01)

PERSPECTIVES OF MODERNIZATION OF WIRE MILL OF HOT ROLLING 150 AT RUP “BMZ”
by: A. V. Gontarj, et al.
Published: (2004-08-01)

Determination of destruction cause of experimental mill roll of stand roughing group of mill 150.
by: I. A. Guzova, et al.
Published: (2021-12-01)

POSSIBILITY OF THERMAL MECHANICAL PROCESSING ON MILL 150 OF RUP “BMZ”
by: V. A. Matochkin, et al.
Published: (2007-02-01)

ASSIMILATION OF HIGH-SPEED OF CORD ROLLED WIRE ON MILL 150 OF RUP “BMZ”
by: V. A. Matochkin, et al.
Published: (2008-08-01)

DEVELOPMENT OF A METHOD OF IMPROVEMENT OF QUALITY OF MILL PRODUCTS AND WEAR RESISTANCE OF THE TOOL AT THE ROLLING MILL 150 JSC «BSW – MANAGING COMPANY OF HOLDING «BMC»
by: I. A. Zuyeu
Published: (2017-01-01)

WAYS TO INCREASE QUALITY OF PRODUCTS AT THE BAR STOCK WIRE ROLL MILL 150 IN OJSC «BSW» – MANAGEMENT COMPANY OF HOLDING «BMC»
by: I. A. Zuyeu,, et al.
Published: (2017-10-01)

PECULIARITIES OF INFLUENCE OF THERMO-MECHANICAL PROCESSING IN PRODUCTION LINE OF MILL 150 OF THE BELARUSIAN METALLURGICAL WORKS ON QUALITATIVE CHARACTERISTICS OF HIGH-CARBON ROLLED WIRE
by: V. A. Lutsenko, et al.
Published: (2012-11-01)

Ensuring the safety of the surface of calibrated rolled products in the conditions of small-grade wire mill 370/150 OJSC «BSW – Management Company of the Holding «BMC»
by: I. A. Kovaleva, et al.
Published: (2020-01-01)

1703 and 1704 Georgia-Abkhaz Campaign and the Cost of the Campaign
by: Eyüp Kul
Published: (2023-12-01)

ROLLING BY “SLITTING-PROCESS” IN FOUR STRINGS OF REINFORCING STEEL ON MILL 320 RUP “BMZ”
by: A. V. Rusalenko
Published: (2004-08-01)

Economization of production of the mill bar and rolled wire
by: S. M. Zhuchkov
Published: (2003-08-01)

Improvement of the technological process of manufacturing bearing grades of steel at the 370/150 mill.
by: V. S. Puteev, et al.
Published: (2021-09-01)

PECULIARITIES OF RECONSTRUCTION OF TAIL UNIT OF WIRE MILL 150 OF BELORUSSIAN METALLURGICAL WORKS
by: N. V. Andrianov, et al.
Published: (2007-02-01)

INFLUENCE OF DEFORMATION IN THE LINE OF WIRE MILL 150 ON DISPERSION OF PEARLITE OF STEEL 80K
by: V. A. Lutsenko, et al.
Published: (2014-07-01)

DEVELOPMENT OF ROLLED PRODUCTION ON SMALL-SECTION MILL 320 RUP «BMZ» IN 2009
by: A. V. Rusalenko, et al.
Published: (2010-05-01)

INFLUENCE OF THE REGIMES OF COOLING OF THE ROLLED WIRE WITH DIAMETER 5,5-9,0 MM OF LOW-CARBON TYPES OF STEEL AT THE MILL 150 AND OF STORAGE DURATION ON STRIPPABILITY OF CINDER IN MECHANICAL WAY
by: N. V. Voronov
Published: (2005-08-01)

DEVELOPMENT OF THE TECHNOLOGY OF THE REINFORCED STEEL OF TYPE (GROUP) BST550 PRODUCTION ACCORDING TO THE AUSTRIAN NORMS IN CONDITIONS OF THE MILL 320 OF RUP "BMZ"
by: A. V. Rusalenko
Published: (2006-05-01)

IMPROVEMENT OF CALIBRATION OF CONE-SHAPED ROLLS OF THE PIERCING MILL OF THE PIPE-ROLLING SHOP
by: V. S. Korovin, et al.
Published: (2017-07-01)

Rolling out defects during rolling of castings at the mill 850 of Belarussian metallurgical plant
by: V. I. Scherbakov, et al.
Published: (2001-11-01)

EXPERIENCE OF IMPLEMENTATION OF THE LABOR PROTECTION CONTROL SYSTEM AT RUP «BMZ» IN ACCORDANCE WITH INTERNATIONAL STANDARDS OHSAS 180001 AND STATE STANDARD STB 18001
by: I. N. Zhuk
Published: (2010-05-01)

SYNTHETIC APPROACH TO THE DEVELOPMENT OF TECHNOLOGY FOR MANUFACTURE OF COLD-DEFORMED REINFORCEMENTS IN ACCORDANCE WITH THE REQUIREMENTS OF TECHNICAL REGULATIONS AND MARKET
by: V. V. Belash
Published: (2018-01-01)

ASSIMILATION OF THE TECHNOLOGY OF ROLLING BY “SLITTING-PROCESS” IN FOUR STRINGS OF REINFORCING STEEL NO 12 AT CONTINUOUS SMALL-SECTION MILL 320 OF RUP “BMZ"
by: N. V. Andrianov, et al.
Published: (2005-05-01)

MODERNIZATION OF TRACKING SYSTEM OF SECOND LEVEL OF ROLLING MILL 850
by: A. N. Guzov, et al.
Published: (2009-05-01)

MODELING OF THE STRESSEDLY-DEFORMED STATE AT ROLLING OF SLUGS AT SECTION MILL
by: A. B. Steblov, et al.
Published: (2005-02-01)

Research on the effect of the grooving of mill rolls of the reeling tube mill on the wear of the elongating mandrel
by: Yu. L. Bobarikin, et al.
Published: (2019-01-01)

Efficacy of Stb resistance genes and pathotype diversity in Zymoseptoria tritici from Ethiopia
by: Ayantu Tucho, et al.
Published: (2025-07-01)

HIGH-DURABLE TECHNOLOGICAL AUXILIARIES FOR ROLLING MILLS OF RUP “BMZ
by: S. S. Gurin, et al.
Published: (2005-05-01)

ANALYSIS OF THE MODERN STATE AND THE DIRECTION OF DEVELOPMENT OF THE ROLLED WIRE PRODUCTION AT HIGH-SPEED WIRE MILLS TECHNOLOGY
by: V. A. Matochkin
Published: (2007-02-01)

FEATURES OF HIGH CARBON WIRE ROD THERMOMECHANICAL WORKING IN A STREAM OF HIGH-SPEED WIRE MILL 150 OF «BSW»
by: V. A. Lutsenko, et al.
Published: (2012-09-01)

Modern materials for cast rolls of hot strip mills
by: Vyacheslav Goryany, et al.
Published: (2022-09-01)

Clad rolled reinforcing bars
by: E. S. Ovchinnikov, et al.
Published: (2020-10-01)

SYNTHESIS AND SIMULATION OF ELECTRIC DRIVES CONTROL SYSTEM OF ROLLING MILL CONVEYORS
by: D. N. Tsapko, et al.
Published: (2019-06-01)

DEVELOPMENT AND IMPLEMENTATION OF PRODUCTION TECHNOLOGY OF REINFORCING THERMOMECHANICALLY STRENGTHENED ROD OF PERIODIC SHAPES NO 16-20, RECEIVED BY MULTISTRAND ROLLING WITH LONGITUDINAL SEPARATION OF BREAKDOWN IN CONDITIONS OF MILL 320 RUP «BMZ»
by: M. A. Murikov, et al.
Published: (2008-11-01)

Assessment and comparison of fatigue in shift workers of a rolling mill and a steel production company
by: marziye Abbassinia, et al.
Published: (2013-02-01)

THE INCREASE OF SERVICE DURABILITY OF THE TECHNOLOGICAL TOOL OF PIERCING MILL OF THE TUBE-ROLLING SHOP
by: A. V. Vengura, et al.
Published: (2013-11-01)

Selection of the optimal version of the rolling rings of stand no. 7 of mill 150 of OJSC “BSW Management Company of Holding “BMC” from various types of high-speed steel, providing the best indicator of operational durability
by: I. A. Guzova, et al.
Published: (2020-01-01)

Determination of the optimal horizontal boring mill for the repair of the pipe-rolling reduction-stretching mill’s body stands
by: O. N. Filonchik
Published: (2022-03-01)

TECHNOLOGY OF HEATING OF THE UNINTERRUPTEDLY CASTED SLUGS IN THE FURNACE OF MILL 150 RUP “BELORUSSIAN METALLURGICAL WORKS” AT THE MINIMUM POSSIBLE FUEL CONSUM PTION
by: V. I. Timoshpolskij, et al.
Published: (2004-02-01)