-
161
-
162
辊压机辊轴快速拆卸复合结构应力分析及应用研究
Published 2021-01-01“…It’s difficult to dismantle the reducer and bearings,when maintaining the roller press.So a new structure related to a link construction between the output shaft of the reducer and the axis was designed to replace them quickly.The construction mainly used end face key connection and bolt connection to transfer the torque and bending moment.However when caculating the stress of the structure by hand,it’s difficult to allot the proportion load between the key and bolts.Ansys software was used to analyze the stress of the structure.The quick replacing structure was modeled,meshed,constrained and loaded.Different detailed structure and bolt preload was considered.The analysis result shows that the preload affects composite structure stress the most.Structural change has a certain effect on the composite structure stress.The materials of bolts and key have great influence on the bearing capacity of composite structure.For RP140-65 roller press,the optimum parameters are selected.The preload should be set to 200 kN~ 250 kN.Non-through keyway composite structure makes the key stress lower.Key material should be selected higher performance than 45 steel.Bolts performance class should bet 12.9.After the drawings was designed,the structure was manufactured and put into operation.It’s proved that the structure design is reliable after it has run for five years.This design method can be popularized and applied in the design of roller press.…”
Get full text
Article -
163
Buckling suppression of a cantilever structure with a modified fuzzy sliding mode control
Published 2025-02-01“…Due to the laminated composite structure, shear effects on the dynamic behavior of the structure are incorporated into the development of the equations of motion. …”
Get full text
Article -
164
MODIFYING OF CAST IRON WITH ULTRADISPERSE ADDITIVES
Published 2017-03-01“…The composition, structure, methods of receipt of ultradisperse materials (UDM) and the prospect of their application in engineering procedures of foundry production are considered. …”
Get full text
Article -
165
LOW SPEED IMPACT PERFORMANCE AND APPLICATION OF FLAX-BASALT FIBER COMPOSITES (MT)
Published 2022-01-01“…The tensile, shear and impact resistance properties of the composite structure were discussed through test and simulation analysis. …”
Get full text
Article -
166
Deep neural networks and humans both benefit from compositional language structure
Published 2024-12-01“…A fundamental property of language is its compositional structure, allowing humans to systematically produce forms for new meanings. …”
Get full text
Article -
167
Plant Cell Wall-Like Soft Materials: Micro- and Nanoengineering, Properties, and Applications
Published 2025-01-01“…Highlights This review provides a detailed account of engineered plant cell wall (CW)-mimetic soft materials, which are designed to replicate the intricate composition, structure, and mechanical properties of natural plant CWs. …”
Get full text
Article -
168
Numerical Analysis of Two I-shaped GFRP Composite Bridge with Corrugated Webs
Published 2021-01-01“…To overcome these disadvantages, some composite structure systems are proposed, such as GFRP-concrete composite structure system. …”
Get full text
Article -
169
OPINIONS ABOUT ALLOTTING STRAINS ON THE LAYERS OF A LAMINATED MONOLITH COMPOSITE
Published 2016-03-01“…The study can be developed to optimize the organization of layers, depending on the practical purpose of using the composite structure (mechanical, thermal and / or sound). …”
Get full text
Article -
170
Study on the Static Performance of Prefabricated UHPC-Steel Epoxy Bonding Interface
Published 2021-01-01“…Prefabricated UHPC-steel composite structure can make full use of the two materials’ mechanical and construction performance characteristics, with super mechanical properties and durability, which has been proved to be a very promising structure. …”
Get full text
Article -
171
A simplified hardness model for WC-Co-Cubic cemented carbides
Published 2021-01-01“…The current work presents an approach to predict the hardness of three-phase WC–Co–Cubic cemented carbides, which establishes a relationship among composition, structure and mechanical performance. With the input of initial composition and grain sizes of carbides, structural parameters needed to predict the hardness can be calculated by thermodynamic calculations and diffusion simulations. …”
Get full text
Article -
172
Equivalent Modal Damping Ratios of a Composite Tube-Type Tall Building to Dynamic Wind Loading
Published 1996-01-01“…The equivalent damping ratio of a composite structure under wind-induced vibrations encompasses the combined effects from the different values of damping, mass, and stiffness of the external and internal tubes. …”
Get full text
Article -
173
Detailed Parametric Investigation and Optimization of a Composite Wing with High Aspect Ratio
Published 2019-01-01“…Then, the analysis of laying methods of skin structure is conducted. Finally, the composite structure is proved to reduce the maximum deformation and maximum stress effectively compared with the metal wing.…”
Get full text
Article -
174
Statistical Analysis of Metagenomics Data
Published 2019-03-01“…We place particular emphasis on the compositional structure of microbiome data. We describe the principles of compositional data analysis and distinguish between standard methods and those that fit into compositional data analysis.…”
Get full text
Article -
175
Design of Clamping Mechanism for Transmission Tower Climbing Robots
Published 2022-04-01“…According to the motion environment and clamping mode of the climbing robot,a composite structure combining magnetic adsorption and mechanical clamping is designed to ensure the reliability and accuracy of clamping. …”
Get full text
Article -
176
Using thermal treatment for hardening corrosion-resistant coatings surfaced with a flux-cored wire containing BN-TiB2 -ZrB2 complex
Published 2018-04-01“…It is shown that the hardening of the metal of such a coating after quenching consists in formation of a complex composite structure with an iron-chromium martensitic matrix, a large amount of eutectic and particles of hardening complexes, which leads to an increase in hardness and wear resistance. …”
Get full text
Article -
177
RESIDUAL STRENGTH EVALUATION OF COMPOSITE LAMINATES REPAIRED BY RIVETED METAL PATCH
Published 2016-01-01“…Fastened joint repair is a main repair method for composite structure with advantages of easy disassembling,high load transferring capacity. …”
Get full text
Article -
178
Prosodic organization of English folk riddles and the mechanism of their decoding
Published 2016-12-01“…Within the process of cognitive model formation the author performs a conceptual analysis of the riddle compositional structure, presented as a systemic algorithmic scheme. …”
Get full text
Article -
179
Application of martensitic SMA alloys as passive dampers of GFRP laminated composites
Published 2013-01-01Get full text
Article -
180
The Mechanism and Application of Deep-Hole Precracking Blasting on Rockburst Prevention
Published 2015-01-01“…The bursting proneness of the whole composite structure could be weakened by the deep-hole precracking blasting. …”
Get full text
Article